Reed pipe

“ A fire pressure is much greater. Therefore, all direct-pressure pipes of lead should be extra strong. Tank-pressure pipes, those which connect with a tank in the attic or above a water-closet, may be medium strong. The terms “extra strong” and “medium strong,” as here used, are definite in their meaning, and apply to regular grades of pipe. The interior fixtures of an ordinary dwelling-house are supplied with lead pipe five-eighths of an inch in diameter, or iron pipe three-quarters of an inch in diameter. ”

“ There is no advantage in coating the surface of the pipe. To prevent decay, such pipe should carry water under pressure or be laid in a saturated soil, so that the wood of which it is made will always be saturated, and coating the wood may interfere with this. Under these conditions the life of such pipe is not known, but it is evidently very great. Large quantities of wood pipe have been removed from trenches in Boston, New York City. Philadelphia, Baltimore, and elsewhere, usually in perfectly sound condition. It was commonly made of logs of spruce, yellow pine, or oak, from 12 to 18 ft. ”

“ That form has descended to all modern piping for water, steam, and gas, because the best that a pipe can take. No other shape has, proportionately to capacity, so little surface for friction inside or rust outside. A locking-bar water pipe, devised by Mephan Ferguson, of Perth, Australia, is made of two plates of equal width, curved into semi-circles which are pressed at their ends into channel bars of [46] soft steel. As the locking-bars and joints are opposite each other, their joints can be tightly closed by a simple machine which exerts pressure in a straight line. ”

“ The lead is put on the thread and when the thread is made up the lead will have been forced into any imperfection that may be in the threads and the joint will then be water-tight. White lead and oil should be used on nickel-plated pipe as other pipe compounds are too conspicuous and look badly. A pipe compound should be used with discretion, for if too much is put on a burr of it will collect in the bore of the pipe and reduce it considerably. ”

“ Investigation justified the assumption that wood pipe under a pressure of 130 lb. would give satisfactory service for 25 years, on which basis it would be less expensive than cast iron, and therefore it was used. Cast iron was considered preferable to steel for pressures not exceeding 310 lb. on account of its greater durability.
Wood Pipe.—Machine-made, spirally-wound, wood-stave pipe, made in sections from 8 to 12 ft. long, with the exterior surface covered with a heavy coat of asphalt, was selected in preference to unprotected, continuous, stave pipe. ”

“ There are many makers beyond reproach, and there are scores of pipes showing patent methods of jointing more or less complicated. The majority of the improvements refer to the fast seating of the ends of the pipes in cradles, well covered in cement, and one especially much in use, Stanford’s, provides a ring of material fitting truly upon a ring of similar material in the socket of the pipe, so that when the two ends are put together, with a little grease or resin between them, the pipes fit closely in every direction, and require but little other luting. ”

“ All the fittings in the pipe system of a plant should be of the best quality, and the piping for high pressures should be extra heavy to withstand the test of time and usage. Water pipes, when of commercial wrought iron, should be galvanized.
In laying out a line of piping or in replacing a portion of an existing line the measurements should be taken from center to center of the various fittings; the allowance for the threaded part of the pipe can be made after the center-to-center and over-all measurements have been made and before the pipe is cut. ”

“ For this reason, ventilating-pipes should never be made of thin iron (galvanized iron) , and should always be protected by a tar-coating. The crowns of lead traps (especially of water-closets) are often bitten into by rats in search of water. In all cases when the crown of a trap is perforated, there is rarely any leakage of fluid to indicate it, but offensive gases escape. All corroded traps and pipes [Pg 60] should be replaced by new ones, and not patched up. Holes in iron pipes may be closed by iron bands surrounding the pipe, and fastened with red-lead putty and screw-bolts (Fig. 32) . ”

“ Like any other device for heating, the perfect and satisfactory results depend altogether on the manner of setting them. In no case should a heater be expected to develop its full power when placed in a fire-place in so close proximity with the brick as to allow the hot air to strike against and be absorbed by them. The heater should be enclosed in a jacket of sheet-iron, having an 8-inch opening, and a collar at the top. Attached to the collar, and “built in” the chimney, should be an 8-inch tin pipe, connecting with the register-box in the second story. ”

“ Wrought-iron pipes, with screw joints, are used by the Durham House Drainage Company, the joints being gas-tight. They have the advantage of being very durable and impervious to gases, but the disadvantage of being too permanent. If it is desired to change the position of a fixture, or to connect a new one, it is easy to break a hole in a cast-iron pipe, or to remove a portion of it, but where wrought-iron pipe is used this is almost impossible. ”

“ Teit by the Indians for the making of the flange or other thickening at the mouth of the pipe stem was to prevent the string used in attaching the pipe to the wooden stem slipping off. According to all of them, wooden stems were always used with tubular pipes as with elbow and simple bowl pipes; for a person cannot smoke any kind of stone pipe more than a few draws before it becomes too hot for the lips. To Mr. Teit's mind, no matter how small the bore of the pipe, a regular stem must have been used for smoking. ”

“ The hot-water flow pipe close to a water back or coil frequently becomes thickly covered with scale. If the pipe is brass, it may be disconnected and treated with acid and then washed out with hot water. If the pipe is galvanized iron and in bad condition, it will probably be more satisfactory to replace it with new pipe. ”

“ All joints in the iron drain-pipes, soil-pipes, and waste-pipes must be so calked with oakum and lead, or with cement made of iron filings and sal-ammoniac, as to make them impermeable to gas.
27. All connections of lead with iron pipes must be made with a brass sleeve or ferrule, of the same size as the lead pipe, put in the hub of the branch of the iron pipe, and calked in with lead. The lead pipe must be attached to the ferrule by a wiped joint. ”

“ It would be infinitely better to run the pipes at once through the wall to the outside. Few persons have any idea of the carelessness of plumbers’ work—of the bad junctions, and of the rapidity with which pipes get out of order and decay. When a leaden pipe carrying water is led into a water-closet discharge pipe, it is frequently simply puttied in, and very soon the dried putty breaks away, and there is a complete leakage of gas into the house. Even if well joined the lead pipe will, it is said, contract and expand, and thus openings are at last formed. ”

“ This was a mistake, for bored pipe has a rough interior and a reduced capacity. The inspection and culling are difficult and unsatisfactory, and imperfections readily apparent in a stave frequently escape detection in bored pipe.
Pipe Joints.—The chamber and tenon of this pipe is an all-wood joint, 4 in. deep. An iron sleeve makes a better and stronger joint. It compensates for any lack of initial tension in the banding over the chamber of the wood joint, and secures full advantage of the swelling of the wood. Cast iron is better than steel ”

“ To avoid these conditions, the piping should be of brass or lead and the storage tank should be of copper. The installation cost of brass and copper is greater than steel, but they will not have to be replaced in two or three years, as is the case with other material. A valve should be placed on the cold-water supply to control the entire hot-water piping system. A pipe with a stop cock should be placed underneath the boiler and should extend [129] into a sink in the basement so that the boiler can be drained at any time for cleaning or repairs. ”

“ It is bad practice to support the main steam pipes over boilers by hangers from the building as the building may settle in a different degree from the boiler hence the steam pipes are not properly supported, i.e., they are either strained unnecessarily by the strain upon the hangers or they are permitted to support themselves; it is better to support them by iron props underneath, made by screwing a flange upon the end of a piece of pipe of proper length and having a wrought iron crotch with thread and nut for adjustment inserted in the upper end. ”

“ Drawn lead pipe is a material possessing many merits, and hence it is used extensively. It should be remembered, however, that soft water attacks lead, and a sufficient amount of [41] lead is occasionally dissolved to cause dangerous poisoning of persons drinking water from such pipes. It is a good precaution in the case of new pipes to allow the water to run for a while, especially if it has been standing in the pipes over night. Tin-lined pipes, although more expensive, are much safer for use, but great care must be taken in making joints in such pipe, lest the tin be removed at the joints. ”

“ Cement and Vitrified Pipes are used for the manufacture of street and house sewers. In some places vitrified pipe is used for house drains, but in most cities this is strongly objected to; and in New York City no earthenware pipes are permitted within the house. The objection to earthenware pipes is that they are not strong enough for the purpose, break easily, and cannot be made gas-tight.
Lead Pipe is used for all branch waste pipes and short lengths of water pipes. The advantage of lead pipes is that they can be easily bent and shaped, hence their use for traps and connections. ”

“ A more serious objection to galvanized pipes may be the fact that the zinc coating, unless applied with great care, soon wears off and ceases to protect the pipe against rust. Copper tubes, lined with tin, are occasionally used, but are expensive and troublesome to put up. In some of the Eastern States drawn seamless brass tubes are used for hot-water pipes. Their only advantage over lead would seem to be their neater appearance and less liability to sag, although changes of temperature affect brass pipes by expansion and contraction, causing leaky joints. ”

“ Soft pig lead or old scrap lead is suitable for lead joints on cast-iron pipe. About 3/4 pound per inch of pipe diameter is generally required for each joint. The lead is hot enough to pour when it begins to char the paddle used to skim off the impurities. When it cools it must be calked tightly to take up shrinkage. The calking should be uniform around the entire joint and should stop when the lead is tight. Heavy pounding or continued calking may crack the bell of the pipe. ”

“ To make a good, gas-tight, lead-calked joint, experience and skill are necessary. The ring of lead joining the two lengths of pipe must be from 1 to 2 inches deep, and from 1/2 to 3/4 of an inch thick; 12 ounces of lead must be used at each joint for each inch in the diameter of the pipe. Iron pipes are sometimes connected by means of so-called rust joints. Instead of lead, the space between the socket and spigot is filled in with an iron cement consisting of 98 parts of cast-iron borings, 1 part of flowers of sulphur, and 1 part of sal ammoniac. ”

“ Such pipes have usually, but not invariably, a smoother inner surface than those which are unlined, hence, when they are used, less friction is presented to the flow of water, and there is less tendency for the pipe to leak. ”

“ Fittings
"Durham" or "screw pipe" work is the name used to denote that the job is installed by the use of wrought-iron or steel screw pipe. We speak of a "cast-iron job" meaning that cast-iron pipe was used for the piping. A completely different method of work is used when screw pipe is employed for the wastes and vents. When screw pipe is to be used or considered for use, it is well to know something concerning the various makes of screw pipe. Nothing but galvanized pipe is ever used. ”

“ These obstructions are now removed by boring tools forced through the pipe by the hydrostatic pressure. The Superintendent of the Halifax (N. S.) Water-Works records the cleansing of a 12-inch main, 32,000 feet long, in three-fourths of an hour. The preservation of cast-iron pipes, and the prevention of these concretions, are now accomplished by carefully dipping the pipe, previously [129] heated to a temperature of 300 degrees, in a bath of distilled coal tar, mixed, to a proper consistency, with linseed oil, or an oil of the tar. ”

“ This arranges a combination whereby a drip pan can be suspended for catching the drip, the construction being illustrated. It is preferable to line the pans with galvanized iron so as to preclude possibilities of leakage. The wooden construction of the ordinary class is usual.
Ratio of Piping. —Regarding the quantity of pipe required, this in a measure depends upon the insulation of the cellars and the temperature of brine circulated. With brine at a temperature of 10° F., one lineal foot of pipe will supply radiation sufficient for twenty cubic feet of cellar. ”