Water pipe

“ It is far from amusing to awake some zero morning and find the house without water because the well pipe has frozen. It can be thawed with a blow pipe but that means calling a plumber or a handy man who happens to have a tool of this sort. One such experience will keep you from forgetting or neglecting to provide a well cover. Similarly, if you are in doubt whether the pipes from water source to house are below the frost line, a carpet of leaves about two inches thick on top of the ground along the course of the water pipe, will obviate any such unhappy event. ”

“ The middle of a frozen pipe should never be thawed first, because expansion of the water confined by ice on both sides may burst the pipe. When thawing a water pipe, work toward the supply, opening a faucet to show when the flow starts. When thawing a waste or sewer pipe, work upward from the lower end to permit the water to drain away. ”

“ The making of perfect threads on pipe is an important matter, especially on water pipes. If the pipe and the dies were perfect, and the mechanic used sufficient oil in cutting, and the fittings were perfectly tapped to correspond to the dies used on the pipe, of course a perfect union between pipe and fitting would result and the joint would be found to be perfect on screwing the pipe home. As all the above conditions are not found on the job, threads are made tight by the use of red or white lead and oil. ”

“ The hot-water flow pipe close to a water back or coil frequently becomes thickly covered with scale. If the pipe is brass, it may be disconnected and treated with acid and then washed out with hot water. If the pipe is galvanized iron and in bad condition, it will probably be more satisfactory to replace it with new pipe. ”

“ Another arrangement is to employ, instead of a cast or wrought-iron pipe, a number of round or flat-iron bars, fastened together at the top and bottom by rivetting to metal hoops in such a manner that intervals are left between each bar, through which the water can pass. Sometimes a solid pipe without the openings is used, but it is not found to be so satisfactory as the perforated pipe, because the latter allows a greater amount of water to pass through it into the soil, thereby furnishing a larger area of moist earth. ”

“ There is no advantage in coating the surface of the pipe. To prevent decay, such pipe should carry water under pressure or be laid in a saturated soil, so that the wood of which it is made will always be saturated, and coating the wood may interfere with this. Under these conditions the life of such pipe is not known, but it is evidently very great. Large quantities of wood pipe have been removed from trenches in Boston, New York City. Philadelphia, Baltimore, and elsewhere, usually in perfectly sound condition. It was commonly made of logs of spruce, yellow pine, or oak, from 12 to 18 ft. ”

“ E and F is a soil pipe 3, 4, 5, or 6 inches in diameter. Note, pipes draining water closets are called “soil pipes”; those draining other fixtures “waste pipes.” N and O represent water-closet flanges; F and H are roof connections; L exhibits double and single Y branches to receive waste-pipes from baths, bowls, or sinks. The plumber makes this connection, always trapping the lead waste-pipe and then soldering it to a brass nipple.
LEAD PIPE JOINTS.
Fig. 160.
It has been remarked that after learning how to make “a wipe joint,” everything is easy relating to the plumber’s trade ”

“ A fire pressure is much greater. Therefore, all direct-pressure pipes of lead should be extra strong. Tank-pressure pipes, those which connect with a tank in the attic or above a water-closet, may be medium strong. The terms “extra strong” and “medium strong,” as here used, are definite in their meaning, and apply to regular grades of pipe. The interior fixtures of an ordinary dwelling-house are supplied with lead pipe five-eighths of an inch in diameter, or iron pipe three-quarters of an inch in diameter. ”

“ Add more thaw pipe at the outer end until a passage is made through the ice. Withdraw the thaw pipe quickly after the flow starts. Do not stop the flow until the thaw pipe is fully removed and the frozen pipe is cleared of ice. A small force pump is often used instead of a funnel and is much to be preferred for opening a long piece of pipe. If available, a jet of steam may be used instead of hot water; being hotter, it is more rapid. ”

“ Such pipes have usually, but not invariably, a smoother inner surface than those which are unlined, hence, when they are used, less friction is presented to the flow of water, and there is less tendency for the pipe to leak. ”

“ It would be infinitely better to run the pipes at once through the wall to the outside. Few persons have any idea of the carelessness of plumbers’ work—of the bad junctions, and of the rapidity with which pipes get out of order and decay. When a leaden pipe carrying water is led into a water-closet discharge pipe, it is frequently simply puttied in, and very soon the dried putty breaks away, and there is a complete leakage of gas into the house. Even if well joined the lead pipe will, it is said, contract and expand, and thus openings are at last formed. ”

“ The planning of hot-water pipes is much more difficult than that of steam-pipes, but the general principle is that the pipes must rise all the way from the boiler to the farther end, where there must be an expansion-box or supply-cistern to allow the water to rise and fall and dissolved air to escape. ”

“ This smaller pipe again discharges the water through an apparatus, attached to either end, into the distributing pipes, for immediate usage upon the banks. The latter-named pipes are still smaller than the others, and are capped with nozzles, the mouths of which are about three inches in diameter. The nozzles are thus small, because larger ones would make the stream of water so large that it could not be thrown against the bank, and yet smaller ones would not furnish enough water for washing away the débris. ”

“ The common method is to lay a galvanized iron pipe in a ditch as far as a spring and there to protect the end of the pipe with a sieve or a grating and to leave it exposed in the water with no efforts expended on the spring itself. ”

“ These pipes must either extend two feet above the highest part of the roof or coping, the extension to be not less than four inches in diameter to avoid obstruction from frost, or they may be branched into a soil-pipe above the inlet from the highest fixture. They may be combined by branching together those which serve several traps. These air-pipes must always have a continuous slope, to avoid collecting water by condensation.
35. Traps of fixtures near the fresh-air inlet may be ventilated by being connected with it.
36. No trap vent-pipe shall be used as a waste or soil pipe. ”

“ Large leaks in a pipe may require cutting out the damaged section and installing a new piece of pipe. At least one union will be required unless the leak is near the end of the pipe. You can make a temporary repair with plastic or rubber tubing. The tubing must be strong enough to withstand the normal water pressure in the pipe. It should be slipped over the open ends of the piping and fastened with pipe clamps or several turns of wire. ”

“ The purifying breezes should blow through in summer and winter without let or hindrance, and to promote their circulation I would, if possible, place the pipe beside a warm chimney. Yet if the air it contains should sometimes move downward it will do no special harm; anything is better than stagnation. Into this open pipe, which should be not only water-tight but air-tight through its entire length, all waste-pipes from the house should empty as turbid mountain torrents pour into the larger stream that flows through the valley. ”

“ CONSTRUCTION DETAILS OF CALORIMETER TABLES
The plumbing includes separate lines of pipe to each hood and table; one each for cold water, steam at from 5 to 10 lb. pressure, compressed air, natural gas, and, in some cases, live steam at a pressure of 60 lb.
On each table is an exposed drainage system of 21⁄2-in. galvanized-iron pipe, in the upper surface of which holes have been bored, through which the various apparatus drain by means of flexible connections of glass or rubber. ”

“ When water from a well is pumped to an elevated tank there is the same necessity of providing about 20 feet difference in level between the tank and the highest fixture, but the length of pipe involved being small, the friction losses are not great. It should be noted even here that too small a pipe may reduce the pressure, a 1/2-inch pipe causing a loss of 47 feet in a 100-foot pipe line. ”

“ To avoid these conditions, the piping should be of brass or lead and the storage tank should be of copper. The installation cost of brass and copper is greater than steel, but they will not have to be replaced in two or three years, as is the case with other material. A valve should be placed on the cold-water supply to control the entire hot-water piping system. A pipe with a stop cock should be placed underneath the boiler and should extend [129] into a sink in the basement so that the boiler can be drained at any time for cleaning or repairs. ”

“ These obstructions are now removed by boring tools forced through the pipe by the hydrostatic pressure. The Superintendent of the Halifax (N. S.) Water-Works records the cleansing of a 12-inch main, 32,000 feet long, in three-fourths of an hour. The preservation of cast-iron pipes, and the prevention of these concretions, are now accomplished by carefully dipping the pipe, previously [129] heated to a temperature of 300 degrees, in a bath of distilled coal tar, mixed, to a proper consistency, with linseed oil, or an oil of the tar. ”

“ Cast-iron pipes rarely exceed 48 in. in diameter, and even this diameter is only practicable where the pressure of the water is low. In the Thirlmere aqueduct the greatest pressure is nearly 180 ℔ on the square inch, the pipes where this occurs being 40 in. in diameter and 13/4 in. thick. These large pipes, which are usually made in lengths of 12 ft., are generally cast with a socket at one end for receiving the spigot end of the next pipe, the annular space being run with lead, which is prevented from flowing into the interior of the pipe by a spring ring subsequently removed ”

“ Every care should be given to make strong and sound joints for the suction pipe and delivery pipe, as the pump cannot do its proper duty should the pipes be leaky or draw air.
To find the total weight or pressure of water to be raised from a well, reckon from [23] the water level in the well to the delivery in the house tank or elsewhere. For example, if the well is 27 ft. deep, and the house tank is 50 ft. above the pump barrel; then you have 77 ft. pressure, or about 39 lb. pressure per sq. in. That portion of the pipe which takes a horizontal position may be neglected. ”

“ Investigation justified the assumption that wood pipe under a pressure of 130 lb. would give satisfactory service for 25 years, on which basis it would be less expensive than cast iron, and therefore it was used. Cast iron was considered preferable to steel for pressures not exceeding 310 lb. on account of its greater durability.
Wood Pipe.—Machine-made, spirally-wound, wood-stave pipe, made in sections from 8 to 12 ft. long, with the exterior surface covered with a heavy coat of asphalt, was selected in preference to unprotected, continuous, stave pipe. ”

“ The pipe also, through which the water is drawn up, must be stiffened and distended by means of metal rings; otherwise the external air, on the first stroke of the pump, would compress the pipe, so that it could admit no water. It is here seen that pipes made of sail-cloth are not so new an invention as many have supposed. That our present apparatus for conveying water256 to the fire-engine is much more ingenious, as well as convenient, must be allowed ”

“ The water in the leaden pipes, leading from the large iron ones underground, into the houses, is frozen. As some part of the pipe is generally exposed to the cold air, this stoppage frequently happens in a frost, so that the turn-cock is obliged to put a small wooden pipe into one of the large ones underground, [75] that the people may procure water. ”

“ A pipe is passed down the borehole to the desired depth, and connected with air-compressors at the surface. The compressors being set to work, the air is caused to issue from the lower end of the pipe and to mix in fine bubbles with the rising column of water, sometimes several hundred feet in height. ”

“ MANHOLE COVER HOLE FOR PIPE TO PUMP CEMENTED JOINTS CONCRETE OR CLAY MANHOLE COVER
A driven well, which is successful in some locations, can be made by two men also, although it’s not an easy job. The point, a special length of pipe with a sharp steel point and screened openings to let the water in, is driven into the earth with a heavy maul or with a weight on a block and tackle. It is not practicable to sink such a well over 100 feet—a drilled well is easier and less trouble. ”

“ This friction between the sides of the pipe and the water, which must be duly considered in a pipe of small size, increases very rapidly as the velocity of the flow increases. It is always a great temptation to use a small pipe, since the cost of the pipe increases rapidly as the diameter increases, but it is penny wise and pound foolish to lay a line of pipe several thousand feet long to furnish water to a house and find when completed that the amount of water furnished by the pipe is on account of friction only a small dribble. ”