Wire netting

“ Another advantage of high tension is the small effect of line resistance upon the current, a consequence of which is that mines may be fired at long distances from the machine, and through iron wire of very small section. A disadvantage of high tension is the necessity for a perfect insulation of the wires.
When electricity of low tension is employed, the [50] insulation of the wires needs not to be perfect, so that leakages arising from injury to the coating of the wire are not of great importance. In many cases, bare wires may be used. ”

“ In some of the newer cables wires covered with cotton soaked in paraffine are used instead of gutta-percha-covered wires. The distances within this city are so short that neither induction nor retardation has to be considered in the telegraph wires. Electric-lighting wires, we have seen, are not affected. The telephone wires are in Paris protected from these evils by an extremely simple though expensive device. Instead of a single wire for each circuit, two wires twisted together are used, the current going out over one and returning over the other. ”

“ The insulated wires being drawn into them, any short circuit or heating of the wire cannot give rise to a fire, as it can only take place in the interior of a non-inflammable tube. A third system of electric light wiring is the safety concentric system, in which concentric conductors are used. The inner one, which is well insulated, consists of a copper-stranded cable. The outer may be a galvanized iron strand, a copper tape or braid, or a brass tube, and is therefore necessarily connected with the earth. ”

“ Birdcages, meat covers, mouse traps, wire blinds, wire nails, wire latticing, &c., we have long been used to; even girding the earth with land and ocean telegraph wire, or fencing in square miles at a time of prairie land, with wire strong enough to keep a herd of a few thousand buffaloes in range, are no longer novelties, but to shape, sharpen, and polish a serviceable pair of penny scissors out of a bit of steel wire by two blows and the push of a machine, is something new, and it is Nettlefold's latest. ”

“ The piles of this equipment, waiting shipment in the Roebling storerooms, give proof that the satire of the cartoonist and the mockery of the funny writer cannot destroy an ancient faith.
The telephone and telegraph companies use uncountable miles of copper wire in line service and other miles in fine sizes for instrument coils and divers other functions. Electricity as an agent would be a halting cripple without wire. The dynamo would have little more utility than a washtub. Armatures, frames for which are formed from flat steel wire, are wound in the Roebling plant in impressive number. ”

“ If the line wires should happen to come into contact with a power wire, there is danger of damage to the instruments, but if an arrester is connected in the circuit such an occurrence would be prevented by the blowing out of the fuse. ”

“ It is evident that by merely depressing the handle till the upper lever comes in contact with the lower bar of metal at the point A, a current of electricity will flow through the point of contact from the battery wire to the telegraph wire. In order to break the contact or circuit, the operator has simply to desist from depressing the handle of the upper lever, which is instantly raised from contact by the action of the spring at the other end. ”

“ The neutral wire is carried direct to the sign and fuses for that wire are often installed up in the sign, while those for the other side of the circuits must be close to the flasher to comply with the rule which requires fuse protection where a small wire is tapped off from a larger one, unless the fuse in the larger wire is below the carrying capacity of the smaller. ”

“ In the making of wire screens the wire men have taken a leaf from the cloth-mill book, but in weaving a casing of cotton or other fibre around the wire for insulation the process is strongly reminiscent of some of the New England textile mills. Long rows of machines, black and silent and swift, reaching upward toward the ceiling, revolving rapidly on an upright shaft; long arms trailing downward, with wheels and bobbins like fingers plying dizzily but swiftly in and out around the wire which unwinds from its spool and keeps forever climbing. ”

“ In the case of the ungrounded sheath, the latter charges at once through all its length to the voltage of the high-potential wire; at some point, a wire within the cable is close enough to the sheath for an arc to strike across, and the trouble begins. All the wires in the cable are endangered if the cross be with a wire of the primary circuit of a high-tension transmission line. Any series arc-light circuit is a high-potential menace. Even a 450-volt trolley wire or feeder can burn a lead-covered cable entirely in two in a few seconds. ”

“ Underground cables, cables formed of rubber insulated wires, and interior wiring which is properly done, all may be considered to be wiring which is unexposed, that is, not exposed to foreign high potentials, discharges, sneak, or abnormal currents. All other wiring, such as bare wires, aërial cables, etc., should be considered as exposed to such hazards and a fuse should exist in each wire between its exposed portion and the central office or subscriber's instrument. ”

“ Insulate every joint, and don’t leave loose joints; they consume too much current.
Don’t cross wires that are insulated without bushing the overlying wires, and never cross uncovered wires.
123Don’t bring a wire through the floor or back of window without using clay bushings; that’s what they are for.
Don’t run wires (as in Fig. 8) without using a lamp, or cutting wires where X is marked; it saves a short circuit.
Don’t let the wires to your lamps touch brass, except under the screw.
Don’t attempt to connect your design to your “cut-out” until you are sure your switch is open. ”

“ Iron seems to be the most desirable material for guard wires because it gives the required mechanical strength and sufficient conductivity at a less cost than copper, aluminum, or bronze, and is easier to handle and less liable to break than steel. It was formerly the practice to staple guard wires to the tops of poles or to the ends of cross-arms, but it was found that the wire was more apt to rust and break at the staple than elsewhere, and in the better class of work such wires are now mounted on small insulators. ”

“ Whenever possible, the wiring of a house, etc., for bell work, should be done as soon as the walls are up and the roof is on. The shortest and straightest convenient route from bell to battery, etc., should always be chosen where practicable to facilitate drawing the wire through and to avoid the loss of current which the resistance of long lengths of wire inevitably entails. The wires should be run in light zinc tubes nailed to the wall. ”

“ If the needle can be soldered to a metal stand, or the cork covered with tinfoil, the wire is not needed. On rubbing the paper and placing it on the tray, the electricity passes up the wire into the needle, thence into the wire cross, and escapes by the bent portions of the wires, each of which should be filed to a point. In escaping it electrifies the surrounding air, and this, according to the law that “like electricities repel each other,” has a reacting force on the wire arms. Accordingly the windmill begins to turn, and may attain a tolerable rate of speed if the tray is strongly charged. ”

“ In wiring new wooden buildings do not draw wires too tight; the wood may expand and either break wire or cause a weakening of the insulation. In wiring before the plaster is put on, always leave a good length free, so it will not be covered up by the plasterers.
The wire used on the gas fixture is of a special kind, being made for the purpose. It is made in two sizes, No. 22 and No. 24 B. & S. gauge, and with three windings of cotton, three outer layers of cotton and one of silk, or three windings of cotton which is soaked in fireproof preparation, and then wound with silk. ”

“ The natural increase in the number of aerial wires created a demand for better insulation and grouping in cables. Hundreds of miles of No. 12 iron wire were braided and dipped in suitable compound for this use. The annoyance from induction soon made a call for anti-induction cable. This want was supplied by a tin-foil cable so called, in which each conductor, after being insulated, was enclosed in a strip of this tin-foil. Cotton-covered wires to the extent of 50 or 100 were cabled together, and after being saturated with paraffine were placed in a lead pipe. ”

“ No. 24 wire is a good size to use; it can be cotton-covered or, preferably, silk-covered, as in the latter case the insulation is better. Begin by making a hole near the roller in the circle of cardboard that is next to the end where the hole for the screw has been made. Pass about three inches of wire through the hole and then wind it evenly on over the tracing paper from end to end and back again. You ought to have five or six layers of it; an ounce, or an ounce and a half, of wire will probably be enough. When it is all on, make another hole in the disc and pass out the wire. ”

“ In general wiring, use weatherproof office wire, or, better still, well-made electric light wire. For ordinary house work No. 16 B. & S. gauge is preferable; smaller wire means higher resistance and less current at burner. For braided office wire, No. 16 runs about 95 feet to the pound, No. 18 about 135 feet to the pound. The cheaper grades of wire without the patent finish or extra insulation are not worth using; sooner or later trouble will ensue, [Pg 37] and once a house is wired, it is no pleasant job to hunt trouble, especially if the wire was put on before the plaster. ”

“ As you have nothing under the feet to press the strain there, it really falls to the stomach to receive all the hard work. Always leave some slack to the guy wire.
A stack must vibrate to a certain extent, therefore if the guy wires are drawn as tight as they possibly can be, the chances are the result would be a broken wire or an anchor giving way.
[47]
Helper Pulling Guy Wire Up to Stack Band
In using clips to fasten the wire at both ends, they should be a size larger than the guy wire, and when clips are not available, allow about two feet over. ”

“ All branches or taps, from any three-wire system, which are directly connected to lamp sockets or other translating devices, must be run as two-wire circuits if the fuses are omitted in the neutral, or if the difference of potential between the two outside wires is over 250 volts, and both wires of such branch or tap circuits must be protected by proper fuses. ”

“ No joint can possibly be perfect that is not metallically continuous. Careful soldering is the only certain mode of securing this, and that this is practicable is evident from the millions of perfect joints in telegraph wires. To scrape the ends of wire bright, and cover the whole with thin sheet lead, as is done by one firm, is simply to court danger. The absence of joints in wire rope is one great element in its favour.
(21) 5. Attachment to building, how made. Some attach the conductor to the building by copper straps and nails; some use holdfasts, either of copper wire or gun metal ”

“ As the wires must be somewhat loose to allow of the connections being made at the back of the push-button at the wall, they will have to be carefully pushed into the hole, and if they are not tightly held by screws, trouble will result. It is a good plan, when using fine enough wire, to make a sort of eye at the end of the wire and pass the screw through this, instead of merely giving the wire end a turn around the screw and then driving the screw home. ”

“ Wires were then run from the lamp socket through the cork and wood disks and the whole painted with melted paraffin to close all apertures and keep out moisture. Good rubber-covered electric-light wire will do nicely for the wiring outside the house, although, if it can be obtained, a piece of lead-covered paired wire is preferable. These wires must be only long enough to reach inside the house, where they may be joined to the ordinary sort of wire used in electric-bell work for connecting with push button and battery. ”

“ FIG. 24.—Showing how wires are arranged and insulated.
Aluminum wire is very light, and causes very little strain on the pole or cross-arms. It offers more resistance than copper, but some of the larger sizes may be used with equally good results.
Iron wire must never be used, even if galvanized or tinned. It possesses a certain reactance tending to choke off the high frequency currents.
FIG. 25.—Aerial insulator. ”

“ As shown in fig. 638, a wire AX, of non-oxidizable metal, of high resistance and low temperature coefficient, passes over a pulley B mounted on the shaft C. The ends of the wire are attached to the plate E at its ends F and G, the wire being insulated from the plate at G. A spring H holds the wire in tension and takes up the slack due to the expansion caused by the heating of the wire when a current passes through it. ”

“ The things that are done with wire in the Western Electric factories are too many for any mere outsider to remember. Some wire is wrapped with paper tape at a speed of nine thousand miles a day. Some is fashioned into fantastic shapes that look like absurd sea-monsters, but which in reality are only the nerve systems of switchboards. ”

“ It cases wire in asbestos to prevent fire from stopping its work; but perhaps the highest phase is reached in the great cables of copper wires used in telephone service. For these the individual wires are covered with paper of various colors, which serves not only for protection but enables men at the opposite ends of a long cable to pick out unerringly the wires with which connection is to be made. Colors are few but possible combinations are many. ”